• emerson 223a cc[34 KB]
• emerson 505[36 KB]
• emerson 508[32 KB]
• emerson 519[41 KB]
• emerson 540 564 572[36 KB]
• emerson 559[42 KB]
• emerson 571 606 611 612 619 620 624 627 sams 76 11[12 MB]
• emerson 571 606 sams 46 25[9 MB]
• emerson 584[44 KB]
• emerson 600 639 sams 87 6[10 MB]
• emerson 602[61 KB]
• emerson 613c[56 KB]
• emerson 614 637 644 647 manual[15 MB]
• emerson 637 637b 637c sams 97 4[10 MB]
• emerson 637a sams 95a 3[825 KB]
• emerson 640[42 KB]
• emerson 803[53 KB]
• emerson 832b[62 KB]
• emerson 838[60 KB]
• emerson 1005m g[60 KB]
• emerson 1010m g[71 KB]
• emerson 1015[54 KB]
• emerson 1955[40 KB]

• emerson 6719df[5 MB]
• emerson a725[79 KB]
• emerson a725 alternate[63 KB]
• emerson a725 components[21 KB]
• emerson a730 yb126[73 KB]
• emerson a730 yb126 antenna assembly[65 KB]
• emerson a733[64 KB]
• emerson a737 2[40 KB]
• emerson a737[61 KB]
• emerson a802[56 KB]
• emerson a1016[44 KB]
• emerson ept427[5 MB]
• emerson ewf2006 tv[2 MB]
• emerson ewf2704[2 MB]
• emerson ewl20s5[4 MB]
• emerson funai ewc09d5b service manual tv dvd[4 MB]
• emerson lc195em82 lc195em87[4 MB]
• emerson lc200em8[4 MB]
• emerson lc320em8[5 MB]
• emerson lc320em8a[5 MB]
• emerson sylvania syphonic ewc1304 sc313e 6313ce svcman[3 MB]
• emerson tc 1973d (ver.a) tv[859 KB]

Search service manual

General Guidance An isolation Transformer should always be used during the servicing of a receiver whose chassis is not isolated from the AC power line.

Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It will also protect the receiver and it's components from being damaged by accidental shorts of the circuitry that may be inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown, replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

General Servicing Precautions
1. Always unplug the receiver AC power cord from the AC power
source before;
a. Removing or reinstalling any component, circuit board
module or any other receiver assembly.
b. Disconnecting or reconnecting any receiver electrical plug or
other electrical connection.
c. Connecting a test substitute in parallel with an electrolytic
capacitor in the receiver.
CAUTION: A wrong part substitution or incorrect polarity
installation of electrolytic capacitors may result in an
explosion hazard.

2. Test high voltage only by measuring it with an appropriate high
voltage meter or other voltage measuring device (DVM,
FETVOM, etc) equipped with a suitable high voltage probe.
Do not test high voltage by 'drawing an arc'.

3. Do not spray chemicals on or near this receiver or any of its
assemblies.

4. Unless specified otherwise in this service manual, clean
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable
non-abrasive applicator; 10% (by volume) Acetone and 90% (by
volume) isopropyl alcohol (90%-99% strength)
CAUTION: This is a flammable mixture.
Unless specified otherwise in this service manual, lubrication of
contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which
receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its
electrical assemblies unless all solid-state device heat sinks are
correctly installed.

7. Always connect the test receiver ground lead to the receiver
chassis ground before connecting the test receiver positive
lead.
Always remove the test receiver ground lead last.

8. Use with this receiver only the test fixtures specified in this
service manual.
CAUTION: Do not connect the test fixture ground strap to any
heat sink in this receiver.