There is Owner's Manual for GE 15154 GE 7Day Digital Timer available here for reading and downloading. Use the download button below or simple online reader. If you have any questions feel free to contact us through Questions/Answers page. InWall 15086 GE Smart Digital Timer User's Manual. PDF files 1 Views 1451 InWall 15088 Electronic. View and Download GE SunSmart 15312 installation instructions online. Digital timer. SunSmart 15312 Timer pdf manual download. Manuals and User Guides. We have 1 Instruction Manual and User Guide for In-Wall 15086 GE Smart. GE Timers User Manuals, Operation Guides and Specifications Preview. 85 GE Timers manual(s) are available for free PDF download, covering 85 GE Timers model(s). Back to Top1 Back to TopI: GE InWall 15086 GE Smart Digital Timer.

• Ge 15086 Timer Instructions
• Ge Model 15086
• Ge 15086 Instructions

Block Programming:

1. When programming ON/OFF events, all days are indicated by

default. To change the day selection simply keep pressing the Day
key and the display will change as follows:

2. Individual Day (MON, TUE, etc.)
3. MON~FRI; SAT~SUN; MON~SAT; MON~SUN
4. MON~WED~FRI; TUE~THU~SAT
5. MON~WED; THU~SAT
6. Follow the steps above to complete programming.

Reviewing Programs:

1. To review the programs that have been entered, press and release

the “PROG” key. Each time you do this you will be able to scroll
thru the programs.

2. Any program can be edited by pressing the “HOUR”, “MIN”, and

“DAY” keys. Then press the “PROG” key in order to accept the
changes.

3. When complete press the “CLOCK” key to return to current time

and day.

Deleting Programs:

1. To delete a particular program simply press the “PROG” key until

the desired program is displayed.

2. Then press the “HOUR” and “MIN” keys until --:-- is displayed.

Then press the “PROG” key in order to delete this particular
program.

3. When complete press the “CLOCK” key to return to current time

Ge 15086 Timer Instructions

and day.

Electrical Ratings:

120VAC 60Hz
15A Resistive
15A Tungsten
1HP

*When done programming,
close door.

Ge Model 15086

Manual Override:

Pressing the door will override the timer setting and will manually
turn the switch ON and OFF.

Initial Startup:

When you initially program the unit it may be necessary to press the
manual override key as the unit will not look back to determine if it
should be ON. For example if the current time is 2:00PM and you just
programmed the unit to turn ON at 1:00PM, you will need to press
the manual override key to turn it ON. Thereafter, the unit will resume
normal operation (automatic).

MEMORY BACKUP:

This timer is equipped with a rechargeable Ni-Mh battery which will
protect your programs during power failure for up to 30 days.
No need to replace battery.
Note that the screen blanks if the battery is discharged completely.

15086

Manual Version 2

11-24-2009

www.jascoproducts.com

Smart Digital Timer

Installation Instruction

1. Turn OFF the main power.
2. Remove the existing switch.
3. Connect the wires of Timer and wall box as followed by using the wire

nuts provided.
a) Connect the Hot/Live wire of main power to the Black wire from Timer.
b) Connect the Neutral wires in outlet box to the White wire from Timer.
Often neutral wires can be found in the back of the wiring box

Ge 15086 Instructions

wrapped in a wire nut.
c) Connect the Hot/Live wire of Load to the Red wire from Timer.
d) Connect the Ground wire to the Green wire from Timer.
Note: Be sure that all wire nuts are secure.

4. Tuck the wires into the wall box leaving room for the Timer. Using the

screws provided. Mount the timer to the wall box being careful not to
crush any wires.

5. Turn Main power ON

POWER-UP SEQUENCE:

1. Lift up the bottom of the door using a small slotted screwdriver.
2. Position the slide switch to TIMER.
3. Press the “RESET” button using a paper clip.
4. The display should flash 12:00AM on Monday.

Setting Current Time:

1. Press and HOLD the “CLOCK” key during this entire procedure.
2. Press the “HOUR” key to advance the hours.
3. Press the “MIN” key to advance the minutes.
4. Press the “DAY” key to advance the day.
5. If any keys are pressed for a prolonged period, the display will

advance rapidly.

6. Release the “CLOCK” key once the time and day have been entered. Now

the timer is in operation and ready to be programmed. The colon “:” after
the hours will continuously flash indicating that the clock is running.

Programming ON/OFF Events:

1. Press the “PROG” key once. TIMER 1 on - - : - - appears.
2. Using the “HOUR” and “MIN” keys enter the desired ON time. By default

all days are indicated. See block programming below for selecting
different days. When complete press the “PROG” key once.

3. Timer OFF --:-- will be displayed. Using the “HOUR” and “MIN” keys

enter the desired OFF time. By default all days are indicated. See block
programming below for selecting different days. When complete press
the “PROG” key once.

4. If complete press the “CLOCK” key to return to current time and day.
5. Note that a total of 7-ON and 7-OFF events can be programmed.

= Wiring Nut

Typical Wiring Schematic

Black

Black

Light

White

White

White

Red

Green

Ground

Timer

120 VAC

Power

Source

LOAD

LINE

GROUND
TIMER-GREEN
WALL-BARE

NEUTRAL
[WHITE]

LINE
[BLACK]

LOAD
TIMER-RED
WALL-BLACK